Vintage Rides. Permanent Vacation.
Out in the Wild Merch on Etsy

Moped Wrench Guides · Guide 20 of 30

Big bore kits: which one to buy, what you need and how to install it

Jump to a section
  1. The kits, by bike
  2. How to pick one
  3. The parts you need besides the kit
  4. How to install a big bore kit, step by step
  5. Jetting and the plug chop
  6. Break-in after the first 200 km
  7. Why big bore kits fail
  8. Questions riders ask
  9. Sources
70cc Moped Kit Fan T-Shirt by Moped Motel
70cc Moped Kit Fan T-Shirt by Moped Motel. See the T-Shirts.

A stock Puch Maxi is rated between 1 and 2 horsepower, depending on how the factory strangled it. A big bore kit is the oldest argument against that number. It swaps the stock cylinder and piston for a larger pair, keeps the crank and the stroke, and widens the bore. On a Maxi the bore grows from 38 mm to 43.5, 44, 45, 46 or 47 mm, and displacement climbs from 48.8 cc to somewhere between 64 and about 74 cc.

Read the bore and the stroke, never the badge. A 46 mm bore on a 39.1 mm Peugeot 103 stroke works out to 65 cc, and it is still sold as a 70. The number on the box is a marketing size. The bore tells you what you are actually buying.

The kits, by bike

Prices are street prices from European and US parts sellers in November 2026, tax included in euros, shipping extra. They move weekly. A kit listed as fitting a model fits the engine family in that model, so confirm your exact engine before you pay.

Puch Maxi, Magnum and Newport engines

KitBoreSold asCylinderHead in the boxStreet price
Polini 65 Sport43.5 mm65 ccAluminum, NikasilYes, plus carbon reed valve and 20 mm manifoldabout €372
Malossi 6242 mm62 ccAluminum, one-ring pistonNo, keep your stock headabout €366
Airsal Racing 6845 mm68.4 ccAluminum, one-ring pistonNoabout €73
Airsal Alu 70, big fins45 mm68.4 ccAluminumNoabout €84
Airsal Racing 7046 mm70 ccAluminum, NikasilSold both waysabout €158 with head
Athena Alu 70 with intake kit45 mm70 ccAluminum, 12 mm pinYes, plus 2-petal reed valve and manifold for 19 or 21 mm PHBGabout €182 to €203
Parmakit 7045 mm70 ccAluminumNoabout €195
Naraku 7045 mm70 ccCast iron, two-ring piston, long finsNoabout €55
Treat kit, 7-port45 mm70 ccCylinder, piston, ring, pin and clipsNo$101
Reed valve Especiale45 mm70 ccReed valve cylinder, flat exhaust portNo$123
Airsal 7246 mm72 ccNot listedYes$200
Airsal Eurokit 4747 mmAbout 74 ccNot listedYes$165 to $200
Gilardoni 74 reed block kitNot listed74 ccNot listedYes$275

The Polini and the Athena arrive as a system: cylinder, head, reed valve and manifold. Everything else is a cylinder and piston that expects you to bring a carburetor, a pipe and a head. The 46 mm Airsal is the one to note for a stock bottom end, because it fits without milling the crankcase. The Naraku is the cheapest way into 70 cc and suits the two-speed Automatik, P1, one-speed S and N, and two-speed X30 engines.

Tomos A3, A35 and A55

KitBoreSold asCylinderHead in the boxStreet price
Airsal Alu 6544 mm65 ccAluminum, NikasilNot statedabout €76 to €95
DMP Alu Sport 70 (A3 and A35)Not listed70 ccAluminumNot statedabout €84
Alukit 70 (A35 and A55)45 mm70 ccAluminum, head, base and exhaust gaskets includedNo, needs a high compression head$126
Alukit party: 44 mm kit, head and gaskets44 mm70 ccAluminumYes, no reeds, intake or exhaust studs$138
Alukit 70 for the A345 mm70 ccAluminum, piston with 10 mm pinNot stated$135

An Alukit expects a high compression head, and the newer style head is the one to buy. The A3 uses a 10 mm wrist pin, and A35 kits come in both 10 mm and 12 mm versions, so match the pin before you order a piston.

Peugeot 103

KitBoreSold asCylinderHead in the boxStreet price
Malossi Sport 7045.5 mm70 ccCast iron, two-ring piston, 12 mm pinNot statedabout €141
Malossi Alu 7045.5 mm70 ccAluminum, 12 mm pinNot statedabout €265
Polini Alu W 7046 mm70 ccAluminum, hard chrome, one-ring pistonNot statedabout €235
Polini Sport 7046 mm70 ccCast iron, two-ring piston, 12 mm pinNoNot listed
Airsal T6 Racing 7046 mm70 ccAluminum, six transfer ports, two-ring pistonNo, original head gasket includedNot listed

Pair the Polini aluminum kit with at least a 15 mm carburetor and a pipe that likes revs. Polini rates its cast iron 46 mm kit at 5.5 hp at 7,000 rpm. The Airsal T6 is quoted at 5 to 7 hp around 8,500 rpm, and it is not street legal.

Honda Hobbit, Camino and Express

KitBoreSold asCylinderHead in the boxStreet price
DR 70 (Hobbit, Camino, Express)46 mm70 ccNot listedNot listed$185
Polini 70 (Camino 50, PX 50)46 mm70 ccCast ironNot listedNot listed
Extremo 44 (Hobbit)44 mm60.2 ccNot listedNot listed$126

The Polini Camino kit uses a 46 mm bore on a 39.6 mm stroke and is rated at 4.8 hp at 6,300 rpm. The DR kit covers the PA50 Hobbit and the Camino, Express NU50, NA50 and NC50.

How to pick one

Aluminum or cast iron. Aluminum sheds heat faster, which is why tuners choose it, and it wants more frequent maintenance. Cast iron costs less and forgives neglect better. If the bike gets ridden hard and checked often, buy aluminum. If it gets ridden in flip-flops and forgotten, buy iron.

Piston port or reed valve. A piston port kit uses your stock intake. A reed valve kit needs a new intake path and a carburetor to match, so it is the bigger project.

Complete or cylinder only. A cylinder-only kit is the cheap way to start and the expensive way to finish, because the head, carburetor and pipe still have to be bought. Add them to the price before you compare kits.

The safe build. For a bike that has to run every day, a 45 mm aluminum kit around 70 cc, a 15 mm or larger carburetor, a real expansion pipe and careful jetting beats a more extreme kit with a stock carburetor. More carburetor and more pipe means more speed, and more rebuilds.

The parts you need besides the kit

How to install a big bore kit, step by step

  1. Confirm the kit fits your exact engine. The model name does not decide it. Puch alone ran four top ends: seven fins on the 1975 to 1985 Maxi, eight on the 1978 to 1986 Hi-Torque, nine on the 1978 to 1982 Magnum and ten on the 1983 to 1986 Maxi Plus and Dart. Compare the cylinder base, stud spacing, transfer port layout and wrist pin size against the old parts, then test-fit the cylinder dry with no sealant.
  2. Check the bottom end before you spend anything else. Play in the crank bearings, a worn big end or a leaking seal ends a big bore build. Fix it now. A new cylinder on a worn bottom end is the most common way to waste a kit.
  3. Take the old top end off and clean the mating faces. Remove the head, cylinder and piston. Stuff a clean rag around the connecting rod so nothing falls into the case. Scrape the old gasket material off the case and keep every scrap of debris out of the crankcase.
  4. Fit the cylinder dry and deal with the fit. A big bore cylinder rarely drops straight on. If the cylinder fights the studs, file the stud holes until it slides on with almost no force. Chamfer the sharp port edges with small files, because kits ship with them raw, and stop before you start reshaping the ports. If the base gasket arrives uncut, lay it on the cylinder base and trim it to the port shapes. Matching the case ports to that trimmed gasket is the standard step for maximum power.
  5. Build the piston. Fit the wrist pin and new circlips, with the small end bearing fresh. Seat the rings so their ends sit on the locating pins in the ring grooves. Check each ring in the bore with a feeler gauge: a new ring in a new cylinder wants a gap of 0.1 to 0.2 mm, and the ring ends must never sit closer than about 3 mm to any port.
  6. Fit the cylinder. Oil the cylinder walls with two-stroke oil. Line the ring ends up on the pins, squeeze the rings in with your fingers and slide the cylinder down over the studs. It goes on without force. If it does not, something is misaligned, so stop and find out what.
  7. Measure the squish before the head goes on for good. Squish is the smallest gap between the piston crown and the head's squish band. Take the rings off the piston for this check, because the measurement is easier without them. Lay a piece of soft solder across the piston crown, fit the head and gasket and tighten it down, then turn the engine through top dead center by hand. Pull the head and measure the crushed solder with calipers. A street Puch wants 1.0 to 1.5 mm. A race engine runs near 0.8 mm. If the reading is under 1 mm, add a second base gasket to lift the cylinder and measure again. Too tight, and the piston hits the head as the rod stretches under revs. Too loose, and you lose power.
  8. Fit the head and torque it in a cross pattern. Use the kit's gaskets, tighten the nuts in two or three passes to the maker's figure, and turn the engine over by hand. The piston must move freely, with no binding and no scraping. Any resistance is a reason not to start the engine.
  9. Fit the intake, carburetor and exhaust. Bolt up the matching manifold and carburetor, and fit the pipe with a fresh gasket. Check the intake rubber and flange for cracks, because a larger cylinder amplifies every leak.
  10. Set the ignition. On a contact point ignition, set the points gap to 0.35 to 0.40 mm and the timing to 1.2 to 1.4 mm before top dead center. Electronic ignitions such as PVL, MVT and HPI have their own timing values from their makers.
  11. Set the carburetor and test for air leaks. Start the air screw 1.5 turns out from fully closed and fit a jet that errs rich. Warm the engine, then spray a short burst of brake cleaner around the base gasket, manifold, carburetor joint and crank seals, away from the hot pipe and plug lead. If the idle changes, you found a leak. Fix every leak before you touch the carburetor again.
  12. Start it and break it in. Check the oil mix and the fasteners, turn the engine over by hand, then start it and listen for knocks and leaks. Ride the first 200 km on a rich 1:40 mix of fully synthetic two-stroke oil, under moderate, varying load. No full throttle, no long steady cruise. Let it cool, then check the head and base nuts, the exhaust flange, the plug and the fuel system.

Jetting and the plug chop

Every part that lets the engine breathe more asks for more fuel, and the plug tells you whether it got it. Run the bike at full throttle for a few seconds, kill the engine without closing the throttle and read the plug. A light, dry plug is lean, and lean is how a new kit seizes. A wet, black plug is rich. Go up a jet size, chop the plug again, and repeat until the color settles. The plug chop only reads full throttle, so a complex carburetor can still be wrong at half throttle. Read more on reading a spark plug and the carburetor.

Break-in after the first 200 km

The rings keep seating for hundreds of miles. Most kits call for a 300 to 800 mile break-in, and over-revving a new kit is the quickest way to destroy it. Hold the revs down, vary the speed and keep the oil fresh. Re-check the plug color after the first tank, and listen for any change in idle. A kit that was sealed, jetted and broken in carefully runs for years. See premix for the oil ratio.

Why big bore kits fail

Questions riders ask

Will a 70 cc kit fit my engine? Maybe. A model name is not enough. Match the engine family, the top end version, the stud spacing and the wrist pin size, and dry-fit before you commit. See the Puch E50, Peugeot 103, Tomos A3 and Honda PA50 engine write-ups.

Do I need a new crankshaft? A reinforced crank is the right partner for an aluminum kit, mainly for reliability at high revs. A mild build can run on a healthy stock crank, and any crank with a worn bearing gets replaced no matter which kit goes on.

Is a big bore kit legal on the road? Check first. Many states define a moped by engine size and top speed, and a kit that pushes displacement past 50 cc can reclassify the bike as a motorcycle. Some kits are sold for off-road use only. Read moped law basics and call your DMV before you ride it on the street.

How long does it take? A kit goes in over a weekend. A careful build includes the bottom end check, the squish measurement and the jetting, and rushing any of those is how kits get ruined.

Where is the step by step for a particular brand? Start with the install guide, then follow the kit maker's own instructions for torque values and clearances.

Sources

General information from published sources and owner experience. Your bike, your state and your tools may differ, so check your own service manual and local rules. Moped Motel is an independent fan site, not a repair service. No seller, brand or channel mentioned here paid to be included or asked to be, and we have no affiliation with any of them.

All guides are on the Moped Wrench Guides page, with the sources. Want to meet the bikes first? Read Bike histories.

Tangerine Dream T-Shirt by Moped MotelMagnum Sunset T-Shirt by Moped Motel

Vacancy for your closet

T-Shirts, hats, and customs. Checkout happens on Etsy.

Moped Motel is vintage two-stroke moped apparel. We print over 100 moped designs on t-shirts, long sleeves, hoodies, sweatshirts, hats and beanies, inspired by real Puch, Tomos and other classic mopeds. Everything is printed to order, and checkout is on Etsy.

// MOPED ARCADE

Think you know your mopeds?

Name That Moped, Pinball, Blackjack and Stack. Free to play.

Play now
Browse merchBuy on Etsy