Vintage Rides. Permanent Vacation.
Out in the Wild Merch on Etsy

Moped Wrench Guides · Guide 22 of 30

Tires and how to change one

Moped Dirtbag T-Shirt by Moped Motel
Moped Dirtbag T-Shirt by Moped Motel. See the T-Shirts.

Sizing. Check the sidewall before you order anything. Most Puch Maxi models run a 17 inch wheel with a 2.25 x 17 tire, and Puch parts sellers list Maxi tires from 2.00 to 2.50 wide depending on model, market and setup. Match the tube to the tire and the valve to the rim: a Michelin Airstop tube set sold for Puch Maxi bikes uses a TR4 valve. Maxi rims are typically 17 inch, 36-hole spoked or cast.

A Puch Maxi S. Those little 17 inch tires carry everything: check the date code, tread and sidewalls.
A Puch Maxi S. Those little 17 inch tires carry everything: check the date code, tread and sidewalls. Photo: Zeitblick, CC BY-SA 4.0, via Wikimedia Commons.

Pressure. For a standard Maxi on the road, about 2.0 to 2.1 bar (roughly 29 to 30 psi) is a practical starting point, per one Puch parts seller. It is not one fixed number for every rider and tire, so adjust for load and what the tire maker prints on the sidewall.

What you need. Two or three tire levers, a valve core tool, mild soap or tire grease, a pump and, if you want, a bead holder that clamps to the rim edge to stop the tire jumping back out. Skip WD-40; it is not for rubber.

Changing a tire

  1. Support the bike and remove the wheel per your manual. On a Maxi rear, that means the chain and brake as well.
  2. Remove the valve core and let all the air out.
  3. Break each bead loose from the rim by hand, a boot heel or a lever.
  4. Work the first bead off with levers, a few inches apart. Pull the tube out, then take off the second bead.
  5. Inspect the rim, the rim tape, the spoke ends and the inside of the tire for nails or glass. Replace the tire if the date code on the sidewall is old.
  6. Dust the new tube lightly, give it a little air, and fit it so it is not twisted, with the valve through the hole. Note the tire's rotation arrow.
  7. Soap or grease the beads. Fit the first bead by hand. Start the second at the valve and work around.
  8. Do the last stretch by hand if you can. Levers are the usual way to pinch and puncture a new tube.
  9. Push the valve up into the tire and check the bead is not trapping the tube. Inflate to about 2 bar, check the bead sits evenly all the way around, then set final pressure.
  10. Refit the wheel, tighten the axle nuts and check the brake before you ride.

General information from published sources and owner experience. Your bike, your state and your tools may differ, so check your own service manual and local rules. Moped Motel is an independent fan site, not a repair service. No seller, brand or channel mentioned here paid to be included or asked to be, and we have no affiliation with any of them.

All guides are on the Moped Wrench Guides page, with the sources. Want to meet the bikes first? Read Bike histories.

Puch Mopeds Skull Left Chest T-Shirt by Moped MotelNo Pedals No Medals T-Shirt by Moped Motel

Vacancy for your closet

T-Shirts, hats, and customs. Checkout happens on Etsy.

Moped Motel is vintage two-stroke moped apparel. We print over 100 moped designs on t-shirts, long sleeves, hoodies, sweatshirts, hats and beanies, inspired by real Puch, Tomos and other classic mopeds. Everything is printed to order, and checkout is on Etsy.

// MOPED ARCADE

Think you know your mopeds?

Name That Moped, Pinball, Blackjack and Stack. Free to play.

Play now
Browse merchBuy on Etsy